118-06 (SP) Technical Datasheet

ELECTRICALLY CONDUCTIVE, EPOXY DIE ATTACH ADHESIVE

DESCRIPTION 118-06(SP) is a screen-printable, B-Stageable, electrically conductive, one part epoxy coating and adhesive. 118-06(SP) can also be applied by dipping and syringe dispensing. This system features excellent thermal stability, outstanding chemical resistance and excellent high temperature properties. Applications include, but are not limited to assembling electrical and electronic components.

UNIQUE FEATURES

  • Excellent Electrical Conductivity
  • B-Stageablility
  • Excellent Chemical Resistance
  • Low Ionics
  • Outstanding Dispensability
  • Long Screen Life
  • Excellent High Temperature Performance

IONIC CONTENT

Chloride
<10ppm
Sodium
<10ppm
Potassium
<10ppm
(Typical properties are not intended to be used as specification limits)

TYPICAL UNCURED PROPERTIES

Property
Value
Units
Viscosity – Brookfield HAT Viscometer @ 10 rpm @ 25°C
23,000
cps
Specific Gravity
2.68
water = 1
Filler
Silver
N/A
Percent Silver (cured)
>74
%
Theoretical Coverage @ 0.001” Wet Thickness
22
sq in/g
Screen Life
8
hours
Solids
86
%
Color
Silver
N/A

 

TYPICAL CURED PROPERTIES

Property Value Units
Operating Temperature
-55 to +230
°C
Peak Temperature
325
°C
Volume Resistivity
0.0002
Ω-cm
Glass Transition Temperature - Tg
100
°C
Coefficient of Thermal Expansion
50
ppm/°C
T-Shear Strength
2100
psi
Weight Loss @ 300°C, TGA
2.77
%
Differential Scanning Calorimetry (DSC)

Peak Tc
168
°C

delta Hc
-33.4
J/g

CURING GUIDELINES

Temperature (°C) Time (mins)
150
60
175
30
200
15

These temperatures and times are presented as a guide only. The curing times are after substrate has been brought up to temperature. The end-user is encouraged to experiment to determine optimum curing schedule.

HANDLING AND STORAGE 118-06(SP) is a one component epoxy system and is ready to use as received. Product should be stored frozen to maintain consistent flow properties. Allow 118-06(SP) to warm up to room temperature before opening container. Prior to using, mix thoroughly to re-suspend fillers. If needed, 118-06(SP) can be thinned with small amounts of Creative Materials’ 113-12 thinner.

SHELF LIFE

125-01 Part A
 Containers
B-Staged Film
25°C
2 months
1 month
-10°C
6 months
3 months

MIX RATIO (by weight)

125-01 Part A
B-187
100
8.5
Pot life: 4 hours

B-STAGE PROCEDURE Apply adhesive to substrate. Apply heat to advance curing to the non-tacky stage (when cooled to room temperature). A temperature of 125º C for 2 – 3 minutes is required (B-stage time is mass related). The user is encouraged to experiment for optimum drying time at a given temperature. Store on release liner to prevent contamination.

BONDING PROCEDURE To use, carefully align parts to be bonded, apply uniform pressure to maintain location. Follow curing guidelines given above. Timing should start once adhesive and substrate reach curing temperature.

  1. As with all adhesive bonds, surface preparation is a vital part of the process. Carefully clean both surfaces to be bonded with MEK if possible. If MEK is not compatible with the surfaces to be bonded, another suitable solvent may be used.
  2. Allow cleaned surfaces to dry completely.
  3. Die cut 118-06(SP) to the of the size of interface area, remove one of the protective liners, position onto one of the surfaces to be bonded, and warm the substrate/adhesive to 50°C-70°C.
  4. By applying slight pressure, laminate the film/adhesive to the substrate smoothing out any trapped air. Allow to cool to room temperature and peel off the other release liner.
  5. Position the other substrate and apply a clamp to provide constant pressure.
  6. Cure for 1 hour at 150°C.
  7. Remove pressure. Part is ready for use.

HEALTH AND SAFETY Use with adequate ventilation. Keep away from sparks and open flames. Avoid prolonged contact with skin and breathing of vapors. Wash with soap and water to remove from skin.

All technical information is based on data obtained by CMI personnel and is believed to be reliable. No warranty is either expressed or implied with respect to results or possible infringements on patents.

REVISION DATE: 5/22/07 REVISION: E

View the Technical Data sheet in pdf format.

Please contact us today to discuss your requirements.